www.warpknitting4u.com

Pathan Shabbirkhan: what I have learned working w...

2011-10-13T00:36:05.711+07:00

Pathan Shabbirkhan:

what I have learned working with 40 denier Lycra for long time. it is the most sensitive kind of combination with other yarn group, key thing to remember is to very delicately control your Dry and wet process temperature rise and cooling, also any vibration in heat setting equipment also play hidden roll in ultimate final finish properties,

finally i got the correct working for warping

2011-08-12T02:39:20.752+07:00

finally i got the correct working for warping

Hello Vanko,thanks for visiting,I will describe yo...

2011-03-16T20:58:54.944+07:00

Hello Vanko,thanks for visiting,I will describe your request in next post.

Hello Sir, First I'd like to say thanks for yo...

2011-03-11T22:22:46.405+07:00

Hello Sir,
First I'd like to say thanks for your great contribution. I'm newbie in this industry and self studying. Could you pls tell me how to determine or calculate the lycra and nylon composition in powernet fabric when run-in values are known.

@ Deepak, The run-in for Lycra or others elastic y...

2010-12-17T16:23:45.516+07:00

@ Deepak,
The run-in for Lycra or others elastic yarn depend of the fabric construction,whether this fabric need high stretch with low run-in or less stretch mean more run-in and also the composition between Nylon and elastic may vary.

Usually the pre-stretch and final stretch during warping process will recommend from yarn manufacture.More big yarn count the final stretch for

hello sir, how are you? thanks for this knowledge ...

2010-12-09T12:30:03.174+07:00

hello sir,
how are you? thanks for this knowledge sharing site.
i wanted to know how to calculate the yarn run in for the lycra(Stretch Yarns).since i was observing some samples and i found very less run in for lycra,also i request you to please explain the relation of pre stretch of the stretch yarn and run in for the same,and also if possible then explain about how to decide the pre

Dear sir, i wanted to know the standard set-up pos...

2010-12-08T12:05:49.489+07:00

Dear sir,
i wanted to know the standard set-up positions for knitting elements for trickot machines.
for example while setting the needle bar height from the machine bed we set it when the needles are at their lowest positions that is
at 0 degree.
but i dont know the positions for the standerd set-up of the clouser bar,and boath the knock over (Upper & Lower) set ups.if

@deepak: the basic setting of knitting elements (s...

2010-12-03T12:46:15.598+07:00

@deepak:
the basic setting of knitting elements (standard setting) for each type of warp knitting machine could be different,depend of its motion. The basic setting of warp knitting machine mention on working instruction of machine called gang table.

@ anonymous : if you know the chain notation for t...

2010-12-03T12:38:39.743+07:00

@ anonymous : if you know the chain notation for tulle and marquisette and than you can calculate the run-in accordingly.

@deepak : run-in for inlay :
mm/rack = 480(bT+cT).

Dear sir please tel me about the run-in calculati...

2010-11-30T18:50:01.752+07:00

Dear sir
please tel me about the run-in calculation for the in-lay stitch also.is am i right if while calculating in-lay if i count only one leg and half of the loop head?

Dear Auther you are providing realy useful informa...

2010-11-30T14:12:24.688+07:00

Dear Auther you are providing realy useful informations for warknitting thanks for that

i have one request if can provide informations on the standerd set-up of the knitting elements

such as needle hieght we set it at zero degree that is required hieght from the needle bed.
but i want to knwow about the toung position how to determine the exact position, again i know

Dear sir Thanks for the reply! Yes! Again I have ...

2010-10-12T15:55:43.312+07:00

Dear sir
Thanks for the reply! Yes!
Again I have one problem with lycra fabric! On HKS 3/1 ,
GB2:- 23/10// yarn:- 50/48 SD Polyester
GB3:- 10/12// yarn:- 40 lycra

Course: - 16.4
Machine width: - 130”
Finish width: - 56”
Finishing Process: - Relaxing, heatsetting, bleaching, dyeing, stentering.
We are unable to gain proper finish result after

Thanks a lot for your contribution. Your blog is r...

2010-09-22T22:43:20.484+07:00

Thanks a lot for your contribution. Your blog is really helpful for me. I'm newbie in the warp knitting industry and there is no training or learning materials provided for me from my boss. :(

the capability on tricot machines start-up without...

2010-09-15T07:08:58.456+07:00

the capability on tricot machines start-up without take up not cause of the yarn feeding system but cause of the knock-over system (2 points knock over)allowed the loop release from the needle without need to pull by take up roller.(can run with high courses per cm).

Thank you, this very good site. also I want to kno...

2010-09-08T16:55:26.858+07:00

Thank you, this very good site. also I want to know calculation of yarn run in for tulle and marquisette (also marquisette 2 bar?). Any help for these ?

Dear sir,In tricot machine starting-up without fa...

2010-09-08T16:13:32.492+07:00

Dear sir,In tricot machine starting-up without fabric take-up possible. but in raschel machine starting-up only with fabric take-up possible. is it the causes of feeding device of that two kind machine are different? Would you explain about it. Thank you

Thanks so much. This really helps. But like you sa...

2010-09-06T22:41:08.417+07:00

Thanks so much. This really helps. But like you said in the end, this is not for Diabolo beams... and all my beams are Diabolo type. Any help with these types of beams?
Great site. Keep it up!!!

The anti static device installed on the warping ma...

2010-08-27T11:16:19.096+07:00

The anti static device installed on the warping machine use for to reduce event to eliminate the electro static on the yarn sheet due a friction between yarn and other parts on the warping machine which can be influence to the yarn quality such a broken filament,hairnes,slub and fluff.

On the knitting machine,depend of material which use on the knitting machine,the fabric produce on

is there any easy way to dismantle the fabric so i...

2010-08-25T14:46:31.100+07:00

is there any easy way to dismantle the fabric so i can easily analysis it.

If i have the anti static rod installed on my wrap...

2010-08-25T14:28:08.800+07:00

If i have the anti static rod installed on my wrapping machine, does that mean that the material i produce from my knitting machine will have an anti-static affect? Meaning that the fabric wont generate electric when rubbing them together.

Hello Jahanzaib, You can contact Karl Mayer agenc...

2010-08-10T19:22:40.513+07:00

Hello Jahanzaib,

You can contact Karl Mayer agency in your country;

Nazer & Co.
Plot # L-31, Block # 22,
Federal 'B' Area,
P.O. Box 71 07
Karachi - 75950 / Pakistan
Tel.: + 92 /21/6 36 21 21 & 6 36 68 04
Fax: + 92 /21/6 34 10 72 & 6 80 53 23
Ansprechpartner: Abbas + Kamal Mooraj
E-Mail: [email protected] , abrar

hello sir.. my name is M.Jahanzaib Khan. i would l...

2010-08-09T13:29:08.064+07:00

hello sir.. my name is M.Jahanzaib Khan. i would like to ask about warp knitting machine in details how can i contact here some one who could tell me and help me purchasing a warp knitting machine which will be cheap and efficient.

and most importantly, what are those parameters that has to be considered before purchasing or choosing a warp knitting machine for green house shade net

Hello Manoj, Glad to heard from you..again...! Wha...

2010-08-05T22:21:23.804+07:00

Hello Manoj,
Glad to heard from you..again...!
What I know for this machine type the maximum speed is 450-500 rpm,I have seen in one company that machine type was running with 450 rpm.
However,I think you should be happy with this current speed 400 rpm, concerning age of the machine,if I not wrong that machine was build around 1993 is it?

hello sir We want to know what maximum speed we ca...

2010-08-05T15:01:59.301+07:00

hello sir
We want to know what maximum speed we can archive on our RJSE 3/1, 24E, 150” machine number:-78469

Note:- this machine runs with creel & magnate jacquard, current speed on the machine is 400 rpm.

Dear Soewarso, Please click this link for the answ...

2010-07-14T20:57:55.620+07:00

Dear Soewarso,
Please click this link for the answer of your question,thanks
YARN RUN-IN VALUE in mm/rack